Checking Ink Level. Check ink level with the ink tank indicator on the front of the printer. When ink reaches the upper limit line (A), ink is full. When ink is near the lower limit line (B), ink is running low. Refill the ink tank. To check the remaining ink level, visually inspect the remaining ink in the ink tank. Reset Waste INk Canon iX4000, iX5000 Connect the Canon PIXMA iX5000 or iX4000 printer to the power cord. ( note: If the automatic power-on function is enabled in the printer, the printer enters the service mode for the first time, but it will never enter the service mode if the printer is turned off by the Power button. Resetter Reset Canon G1010 G2010 G3010 Service Tool ST5204 V5204. Jakarta Selatan Toko Printer Indonesia. IC Eeprom Eprom + Bios Canon.
hi everybody, while waiting for parts for my next project to arrive, im gonna give a little tutorial on how to reset the canon g2010 printers waste ink counter..im pretty sure anybody who owns a G2010 printer will face this problem sooner or later..so lets get to it.. the tools that you need to do this can be downloaded here :
CANON G2010 SERVICE TOOL
Download and extract using WinRAR or any aps that support unzipping file archive.
Canon G2010 problem code 5B00 mean the waste ink counter overflow, you should be reset Canon G2010 Waste Ink Counter (clear Waste Counters). The printer will blink as follow: Orange light – 7 times. Alternatively Green (Power) and Orange.
And computer show up problem “SupportCode: 5B00”
Resetter Canon Ip1980
Now , enter Canon G2010 service mode:
How to put Canon G2010 printer in service mode :
Step 1: Turn off Canon G2010 printer
Step 2: Press and hold printer’s RESET button
Step 3: Press and hold printer’s POWER button.
Step 4: Released printer’s RESET button, POWER still pressed
Step 5: Press and released Canon G2010 printer’s RESET button 5 times @ 6 times (Bypass scanner)
Step 6: Released Canon G2010 printer’s POWER button:
Now, Canon G2010 printer on SERVICE MODE condition. In this condition, computer detect found new hardware.
Step 7: When computer detect FOUND NEW HARDWARE, press CANCEL
Run the service tool that we downloaded earlier..click on 'Accept'
Now click 'Start' under the Canon Tool
Now click the service tool in the number order...after clicking '1' the printer will print some number code, make sure the printer is loaded with 1 piece of paper.
After clicking '2' the printer will move it printhead a few times, just wait until it stop.
After clicking '3' the printer will print status sheet.
and you are all done, just restart the printer and you can print normally again.
Now check Canon G2010 printer status in Control Panel, If it shows “Printer is online“, your Canon G2010 printer is ready to print – no errors – no waste Counters Overflow.
- Repairing Your Printer
Canon G1010 Resetter Crack
When transporting the printer for repairing it, follow the procedure below to prepare.
Important
Reset Canon G1010
You cannot take ink out of ink tanks.
Do not remove the print head (cartridge).Ink may leak.
When transporting the printer, pack the printer in a plastic bag so that ink does not leak.
Pack the printer in a sturdy box so that it is placed with its bottom facing down, using sufficient protective material to ensure safe transport.
Do not tilt the printer.Ink may leak.
When a shipping agent is handling transport of the printer, have its box marked 'THIS SIDE UP' to keep the printer with its bottom facing down.Mark also with 'FRAGILE' or 'HANDLE WITH CARE'.
Please handle with care and ensure the box remains flat and NOT turned upside down or on its side, as the printer may be damaged and ink in the printer may leak.
If the printer cannot be turned on, unplug it and go to step 4.
If an error has occurred, press printer's RESUME/CANCEL button.
After the Alarm lamp is turned off, go to step 3.
If the error is not cleared, press ON button to turn the printer off, and then unplug it.If the printer cannot be turned off, unplug it.Go to step 4.
Set printer to transporting mode.
Press and hold RESUME/CANCEL button, and then release it when Alarm lamp flashes 8 times.
The printer is set to transporting mode and turned off.
Confirm that the ON lamp is off and unplug the power cord.
Important
- Do not unplug the printer while the ON lamp is lit or flashing, as it may cause malfunction or damage to the printer, making the printer unable to print.
Make sure that print head (cartridge) holder has moved to far right.
If the print head (cartridge) holder is not to the right, move it to far right.
Make sure that tank caps are properly closed.
Retract the paper output tray and the output tray extension, then close the paper support and the document tray.
Unplug the printer cable from the computer and from the printer, then unplug the power cord from the printer.
Use adhesive tape to secure all the covers on the printer to keep them from opening during transportation.Then pack the printer in the plastic bag.
Pack the printer in the box.
Attach the protective material to the printer to pack it securely in the box.